Do you know what inspection should be done after the main part of the universal milling machine is installed?

Universal milling machine is a combination of milling machine parts. All parts need perfect integration and cooperation to realize all functions of #UniversalMillingMachine. Therefore, when the main body of the universal milling machine is installed, the work is not finished and a series of inspection is needed. Today we're going to talk about what else needs to be done.

After the main body of the universal milling machine is installed, the cable, the oil pipe and the gas pipe need to be connected first. All the cables and pipes to be connected shall be properly connected according to the requirements of the electrical wiring diagram and the gas pressure line diagram in the milling machine instruction manual. The connection shall be clean, decontamination and reliable plugging and sealing. When the cable is installed, the fastening screw must be screwed down to ensure the contact of the joint plug is completely reliable. When connecting oil and gas pipes, foreign bodies should be prevented from entering the pipeline, resulting in failure of the whole hydraulic system. Each joint must be tightened, otherwise it will leak in the test and increase the amount of rework.

In addition, it is necessary to check whether the plug-in units in the universal milling machine have any looseness or damage due to long distance transportation, and check whether the components are in good contact with each other. For some imported universal milling machine, often because the work voltage standards are not the same, the need for another transformer. Before switching on, check the voltage and frequency of the input power carefully.

Finally, we should check the connection status of all parts of the milling machine, and check if there is excess thread and pipe joints. Only through careful and careful work, can the universal milling machine be operated smoothly.

For more information, welcome to visit the website：http://www.cndxmc.com/2017/06/29/do-you-know-what-inspection-should-be-done-after-the-main-part-of-the-universal-milling-machine-is-installed/

The classification of universal milling machine milling cutter

Today we are going to talk about milling cutters for universal milling machines.Milling cutter is mainly used for processing plane, steps, grooves, forming the surface and cut the workpiece and so on.The milling cutter of #UniversalMillingMachine is divided by the use, mainly has the following several kinds:

1.Cylindrical milling cutter: used in horizontal milling machine to process the plane. The cutter teeth are distributed on the circumference of the milling cutter and are divided into two kinds of straight teeth and spiral teeth according to their teeth shapes. According to the number of teeth, coarse teeth and two kinds of fine teeth. The spiral tooth coarse tooth milling cutter has few teeth, high strength of the cutter tooth and large chip holding capacity, and is suitable for rough machining; the fine tooth milling cutter is suitable for fine machining.

2.Surface milling cutter: used in vertical milling machine, end milling machine or Gantry milling machine. The end face and circumference have knife teeth, and also have coarse teeth and fine teeth.

3.Vertical milling cutter: used for machining grooves and step surfaces, etc., the cutter teeth are on the circumference and the end face, and can not feed along the axial direction when they are working. When the end mill passes through the center end teeth, it can be axially fed.

4.Three face milling cutter: it is used to process all kinds of grooves and step surfaces, and the two sides and the circumference are provided with cutter teeth.

5.Angle milling cutter: used for milling into a certain angle of the groove, there are two kinds of single angle and double angle milling cutter.

6:Saw blade milling cutter: used for machining deep groove and cutting workpiece, have more cutter tooth on the circumference. In order to reduce the friction between milling and cutting, both sides of the cutter tooth have a 15 ~1 angle vice angle.

In addition, there are keyway cutter, dovetail slot cutter, T-slot cutter and a variety of milling cutter and so on.

#UniversalMillingMachine milling structure is divided into four kinds.

1. integral type: the cutter body and the cutter tooth are made into a whole.

2. whole welding tooth type: cutter tooth with carbide or other wear-resistant tool - made of materials, and brazed on the knife body.

3. insert type: the cutter tooth is fastened with the mechanical fastening method on the cutter body. The replaceable cutter tooth can be the cutter head of the whole cutter material, or the cutter head of the welding tool material. The cutter head is mounted on the cutter body and the grinding cutter is called an internal grinding type; the cutter head is individually worn on the fixture and is called external grinding type.

4. indexable type: this kind of structure has been widely used in face milling cutters, end mills and three edged cutters.

For more information about universal milling machines, welcome to visit the website DXMC.

Universal Milling Machine X6332WA

Universal Milling Machine X6332WA is one of our main products.Let me show you about it.

X6332WA Product Advantage

Cast iron after artificial aging treatment, high precision, long service life.

Gear power feed，motorized lift on Z axis.

The table rotation.

Hardening treatment, rectangular guideway.

Equipped with manual lubricating device, the lubrication on the lead screw and guideway.

If you want to know more details,please visit X6332WA .